How to make the tech 2 support 1988-1998 SAAB cars
Question: One customer bought gm tech2 from us, he sent email to us. “Hi. I get it and it works. One problem. It’s work just […]
Tech2
Resolving the Issue When GM Tech2 Cannot Detect the CANDI Module
Introduction: When it comes to vehicle diagnostics and troubleshooting, the GM Tech2 scanner is an invaluable tool for professionals and enthusiasts alike. However, sometimes users […]
How do I connect my GM Tech 2 to my computer
The Tech2 can be connected to a computer using the serial (RS-232) connector on your computer. Most modern machines don’t have that built-in serial device […]
How To Update Tech 2 Software
The Tech2Win driver must be installed. Table of contents 1. how do i access techline connect? 2. what scan tool does gm use? 3. what […]
GM TECH2 Fix Hummer H3-H2 Mileage Does Not Count After BCM was Change
How To Setup A Bcm On 2008 Hummer H3-H2 The Milage Is Not Counting After The BCM Was Changed after a customer changed the bcm […]
Examining GM Tech 2 Vehicle Network Diagnostic Function
GM Tech 2 GM Tech 2 Vehicle Network Diagnostic Function diagnostic tools and computers scanning vehicles fault codes scan tool diagnositcs vehicle diagnostics automotive aftermarket […]
The 5 Best Gm Tech2 Scanners
Are you looking for a gm scanner for your needs? You are in the right place. We strive to offer our valued customers a reasonable […]
Trying to use a GM Tech2 clone to perform a “VIN Re-learn” for a radio\nav – 2013 Volt
Short version: (out of respect for your time) I have a 2013 Volt (Premium with Nav), vin:1G1RD6E42DU103454 I had to replace my radio\nav unit, and […]
How to delete the Corvette F55 system out of the BCMthe car by gm tech2
If you have a GM Tech II with Candi adapter, you can erase the Corvette F55 system from the BCM/Car in one minute. It’s a […]
How to Solve unable to program the Central Control Module (CCM) using Vetronix Tech2
Autonumen found a good way to solve unable to program the Central Control Module (CCM) using Vetronix Tech2. Here is the solution. Models. 1994-1996 Chevrolet […]
GM Tech2 Tech 2 GM Scanner with CANDI TIS Works for GM/SAAB/OPEL/SUZUKI/ ISUZU/ Holden
Question： ALL connections are secured. When clicking on the GM Tech 2 view icon it opens then get cannot connect to the device error message. […]
Can GM tech2 do the ECU programming of 2007 saab 9-3
Recently, one of our online customers asked whether gm tech2 can do 2007 saab 9-3 ECU programming? The answer is yes. as the picture below. […]
GM Programming Error Codes
Hello everyone, I have documented the GM Programming Error Codes I’ve encountered over the years felt like Diagnostic Network would be a good place to […]
How to Enable Chevrolet Impala Afterblow with GM Tech2
Problem: I am getting a funky smell when I turn the AC on in my 2007 Chevrolet Impala. I figure the cabin air filter has […]
Fuel Injector Balance Test With Tech 2 (With Automatic Transmission)
Circuit Description The Fuel Injector Balance test is performed when a misfire, knock, excessive smoke, or rough running condition exists with no electrical DTCs. During […]
How to bleed the ABS system with GM Tech 2
Both cars and trucks have ABS systems or anti-lock braking systems that require regular maintenance. This GM Tech2 scanner is specially designed for GM vehicle […]
Is possible to change idle speed with GM Tech II
Possible to raise and lower idle speed using a Tech II scanner? Look here – questions and answers from users and technicians 2003 escalade, found […]
1997 Chevrolet 3.1 Lumina loss of power solved with GM Tech2
Car model and year: 1997 Chevrolet 3.1 Lumina with 90K. Issue: A bit of a very slow coolant loss, and the pump was found leaking. […]
Is possible to change idle speed with GM Tech II
Possible to raise and lower idle speed using a Tech II scanner? Look here – questions and answers from users and technicians 2003 escalade, found […]
How to Solve OBD2 Port Not Communicating with Tech 2 Scanner
This is the info needed to build a P10 PCM benchtop harness. Yes, everything works. I bought a USB dongle from Autonumen.com , reconfigured TIS2000, and […]
How to use Tech2 program the Central Control Module (CCM)
Autonumen found a good way to solve unable to program the Central Control Module (CCM) using Vetronix GM Tech 2. Here is the solution. Models: 1994-1996 […]
MDI for GM Scan tool
The new MDI for GM can be used only in the Pass-Thru method. This means you can use it as your programming tool, while your […]